Jaguar - Parts

Home
Parts
Jaguar

Your filters

Model: E-Type

Clear All

Filter by

Group

Jaguar parts
Model: E-Type

Alternator Pulley

C24392

POA (ex VAT)

POA (inc VAT)

Suits the correct twin v belt.

Big End Bearing Shells Std

JAG217

£46.90 (ex VAT)

£56.28 (inc VAT)

Chainguide (exhaust side LH)

XK1487

£174.00 (ex VAT)

£208.80 (inc VAT)

This chain guide is required when fitted a wide angle cylinder head

Spring for detent plunger

C845

POA (ex VAT)

POA (inc VAT)

Braided Cam Oil Feed Pipe (Ally Block W/A

JAG254(KIT)

POA (ex VAT)

POA (inc VAT)

Crankshaft Pulley

XK5773

£105.00 (ex VAT)

£126.00 (inc VAT)

Twin v belt crankshaft pulley

Jaguar LWE engine, wide angle, carburettors, ally block, wet sump

ENGJAGLWE-3

POA (ex VAT)

POA (inc VAT)

Complete engine assembled and dyno tested. We offer 2 standard specifications, Fast road a

Exhaust Manifold, Pair (Wide angle)

JAG298

POA (ex VAT)

POA (inc VAT)

Timing chain-Top for WA head 106

JAG198-106

£49.75 (ex VAT)

£59.70 (inc VAT)

This chain is the best available. For wide angle engines with carburettors

Water pump bearing

JAG130

£39.75 (ex VAT)

£47.70 (inc VAT)

High Quality water pump bearing

Limited Slip Differential; Aluminium

JAG353

POA (ex VAT)

POA (inc VAT)

Oil Filter Base (Ally) for screw-on filter

JAG149S

£335.00 (ex VAT)

£402.00 (inc VAT)

This oil filter housing is only correct for dry sump E-Type engines. This housing is desin

Cylinder head nut

JAG157

£4.45 (ex VAT)

£5.34 (inc VAT)

Requires 14 per engine. This is the correct nut for wide angle head engines

Starter Motor 3.8ltr

JAG389

POA (ex VAT)

POA (inc VAT)

Dynamo Pulley - Duplex Belt

204229

£78.00 (ex VAT)

£93.60 (inc VAT)

Correct type twin V belt.

Exhaust Manifold Plate

JAG191

£22.00 (ex VAT)

£26.40 (inc VAT)

This part only fits Wide angle cylinder heads, 2 parts required

Damper and pulley kit wet sump LWE

JAGLWE-55-060

POA (ex VAT)

POA (inc VAT)

Cylinder Head Wide angle LWE #

C1884-E

POA (ex VAT)

POA (inc VAT)

Oil Delivery Pipe Ally Block, wet sump

C22595AB

POA (ex VAT)

POA (inc VAT)

Timing chain - bottom

JAG199

£41.00 (ex VAT)

£49.20 (inc VAT)

This is the best quality timing chain available. Holds up to the demands of racing

Cylinder Head Stud Set; W/A Alloy Block

XK100-3

POA (ex VAT)

POA (inc VAT)

Correct studs for fitting our wide angle heads to our 3.8 aluminium Cylinder blocks which

Rubber Type Seal For Rear Of Sump

C36499

£7.40 (ex VAT)

£8.88 (inc VAT)

This rubber sealing strip supersedes the earlier cork type.

Bell Housing - 3.8Ltr

JAG252

POA (ex VAT)

POA (inc VAT)

Water ump - LWE

XK5299

£405.00 (ex VAT)

£486.00 (inc VAT)

Aluminium water pump specific to the Light weight E-Type Jaguar. The pulley flange has a 1

Jaguar LWE engine, Wide angle, Carburettors, Iron block, Wet sump

ENGJAGLWE-1

POA (ex VAT)

POA (inc VAT)

Crankshaft (8 Weight) Large Nose

JAG295L

£3,250.00 (ex VAT)

£3,900.00 (inc VAT)

This crankshaft is made to Jaguar light weight E=Type specification with a longer and larg

Cylinder Block In Alloy (wet sump) #

XKC1636W

POA (ex VAT)

POA (inc VAT)

Aluminium Cylinder block to suit Wet sump. 88mm bores

Impellor for water pump

JAG124

£38.50 (ex VAT)

£46.20 (inc VAT)

High quality component made by C&G cast in the UK from our own pattern equipment.

Braided Cam Oil Feed Pipe (steel block N/A)

JAG341

POA (ex VAT)

POA (inc VAT)

Flange for water pump pulley

JAG250

£37.50 (ex VAT)

£45.00 (inc VAT)

To suit a 5/8 water pump shaft. 1.7\" PCD

Breather tube set (wide angle)

JAG146

£165.00 (ex VAT)

£198.00 (inc VAT)

The set comprises of 4 tubes. This is correct for wide angle Heads. The kit is different f

Exhaust Valve Guide

JAG371

POA (ex VAT)

POA (inc VAT)

Crankshaft (12 Weight) Large nose

JAG333L

POA (ex VAT)

POA (inc VAT)

Camshaft bearing shells, Std

JAG184

£47.00 (ex VAT)

£56.40 (inc VAT)

Piston 87mm (Wide angle) 10:1 Compression ratio

JAGLWE-55-041

£168.00 (ex VAT)

£201.60 (inc VAT)

Wide angle piston to suit 87 standard bore size. 10-1 compresion when using a C&G cylinder

Diff cover - aluminium

4HU-004-26A

£192.00 (ex VAT)

£230.40 (inc VAT)

Manufactured from sand cast Aluminium. It has extra bosses for oil cooler take offs. It wi

Camshaft .4375 lift

JAG194

£540.00 (ex VAT)

£648.00 (inc VAT)

This part only fits Wide angle cylinder heads

Alternator Kit

JAGLWE-90-397

POA (ex VAT)

POA (inc VAT)

Belt For Water Pump & Dynamo length 1050mm

C19525

POA (ex VAT)

POA (inc VAT)

Sump

C24457

£645.00 (ex VAT)

£774.00 (inc VAT)

Produced in sand cast alloy from our own pattern and fits both 3.8 and 4.2 engines. This i

Fuel injector inner

JAG240

POA (ex VAT)

POA (inc VAT)

Inlet manifold 0deg 45DCOE #

XK1834-45E

£900.00 (ex VAT)

£1,080.00 (inc VAT)

Suitable for installation in a Jaguar E Type when fitted with our wide angle head and 45DC

Front timing Cover Wet Sump

C8614-1

£236.00 (ex VAT)

£283.20 (inc VAT)

Cast off our own pattern in the uk. Machined in our factory. This is a high quality part

Cylinder Liner

JAG255

£58.00 (ex VAT)

£69.60 (inc VAT)

Replacement liner for our Aluminium Cylinder blocks

Oil filter adaptor

XK5868

POA (ex VAT)

POA (inc VAT)

Adaptor for send dry sump oil to the oil cooler.

Jaguar LWE engine, wide angle, carburettors, ally block, dry sump

ENGJAGLWE-4

POA (ex VAT)

POA (inc VAT)

Dry sump kit (alloy block)

JAG317-AB

POA (ex VAT)

POA (inc VAT)

Camshaft follower 44mm diameter

XK1403-4

£27.50 (ex VAT)

£33.00 (inc VAT)

44mm camshaft follower for wide angle cylinder heads. 12 required per engine

Oil Filter (Spin On)

JAG140

£9.50 (ex VAT)

£11.40 (inc VAT)

For wet sump engines
Thread Size. 1 -12tpi UNF

Sump Baffle (Wet Sump)

JAG358

£525.00 (ex VAT)

£630.00 (inc VAT)

Gasket - Oil Return Pipe (Wet Sump)

C16765

£1.30 (ex VAT)

£1.56 (inc VAT)

Front oil seal dry sump

JAG158

£6.50 (ex VAT)

£7.80 (inc VAT)

This seal only fits Dry sump engines

Exhaust manifold headers pair (STD)

JAGLWE-35-001

POA (ex VAT)

POA (inc VAT)

These exhaust manifolds are specific to the wide angle head and do not fit standard Jaguar

LWE Diff Housing and cover in ally #

4HU-004-25AASM

POA (ex VAT)

POA (inc VAT)

Manufactured from sand cast Aluminium

Inlet valve 3.8 W/A 2 3/32 dia

JAG192

£36.50 (ex VAT)

£43.80 (inc VAT)

This part only fits wide angle cylinder heads
Head diameter 2 3/32, 2.094, 53,2mm

$Clutch plate 9 1/2\" dia 1 1/8\" 10 Spline$

Clutch plate 9 1/2\" dia 1 1/8\" 10 Spline

JAGLWE-80-002

POA (ex VAT)

POA (inc VAT)

Cylinder Head Wide angle E-Type assembly

C1884-EASM

POA (ex VAT)

POA (inc VAT)

Washer for distributor drive shaft

C2393

£9.50 (ex VAT)

£11.40 (inc VAT)

Steel heat treated washer for the distributor drive shaft. Fits between the gear and bush.

Spring Retainer

JAG213

£14.20 (ex VAT)

£17.04 (inc VAT)

This part only fits Wide angle cylinder heads

Camshaft follower 1 5/8 diameter

XK1403-2

£23.10 (ex VAT)

£27.72 (inc VAT)

1 5/8 diameter steel cam followers for use on Wide angle cylinder heads

Crank damper securing bolt

C5896

£28.50 (ex VAT)

£34.20 (inc VAT)

High qulaity crankshft nose bolt made by C&G. Another product we made when we were unable

Oil Delivery Pipe Ally Block, dry sump

JAG253ABDS

POA (ex VAT)

POA (inc VAT)

Water pump pulley

XK5747

£149.00 (ex VAT)

£178.80 (inc VAT)

Twin V belt water pump pulley. This is the best belt to use not only is it the most reliab

Jaguar LWE engine, Wide angle, Carburettors, Iron block, Dry sump

ENGJAGLWE-2

POA (ex VAT)

POA (inc VAT)

Crankshaft (8 Weight) Small Nose

JAG295S

£3,250.00 (ex VAT)

£3,900.00 (inc VAT)

When fitting to an original Jaguar iron blocks the width of the rear main bearing housing

Water pump seal

JAG394

£12.75 (ex VAT)

£15.30 (inc VAT)

$Tappet shim 5/16\" stem$

Tappet shim 5/16\" stem

JAG129

£4.50 (ex VAT)

£5.40 (inc VAT)

We manufacture our tappet shims from ? to ? in 0.005 increments?
We can grind shims

Inlet Valve Guide

JAG351

£24.50 (ex VAT)

£29.40 (inc VAT)

Spigot Bush

C2226

£7.50 (ex VAT)

£9.00 (inc VAT)

Dimensions 3/4\"O.D x 1/2\"I.D x 1.1/8\"Long.

Valve Spring

JAG154

£14.70 (ex VAT)

£17.64 (inc VAT)

Valve springs for wide angle cylinder heads. 12 required per engine

Filter Head With Oil Cooler Connection & Pressure Relief Valve

JAG386

POA (ex VAT)

POA (inc VAT)

Washer for cylinder head nuts

JAG189

£2.75 (ex VAT)

£3.30 (inc VAT)

Requires 14 per engine. This is the correct cylinder head washer for wide angle head engin

Piston 88mm (wide angle) 10.7:1 Std compression height

JAGLWE-55-053

£168.00 (ex VAT)

£201.60 (inc VAT)

Wide angle piston. 10.7 - 1 compresion ration with our cylinder head and Head gasket. Perf

Diff cover - magnesium

4HU-004-26M

POA (ex VAT)

POA (inc VAT)

Manufactured from sand cast magnesium with chromate black finish.

Rear Trunion Bracket (LWE)

C20480

£195.00 (ex VAT)

£234.00 (inc VAT)

Aluminium rear trunion brackets. Cast in the uk from our own tooling. Machined in our fact

Camshaft .520 Lift (Inlet & Exhaust)

JAG195

£552.00 (ex VAT)

£662.40 (inc VAT)

This part only fits Wide angle cylinder heads, 0.530\" lift, 30mm base circle

Cylinder Head Stud Set; N/A Alloy Block

XK100-2

POA (ex VAT)

POA (inc VAT)

Correct studs for fitting a standard Jaguar head to our 3.8 alloy blocks. UNC thread

Crankshaft damper distance piece - wet sump

C34064

POA (ex VAT)

POA (inc VAT)

Sump Gasket (Pair)

JAG247

£16.00 (ex VAT)

£19.20 (inc VAT)

This gasket will on fit dry sump E-type engines only as the front covers are longer than a

Inlet Manifold 0deg 48DCOE #

XK1834-48E

£900.00 (ex VAT)

£1,080.00 (inc VAT)

Suitable for installation in a Jaguar E Type when fitted with our wide angle head and 48DC

Gear lever knob

C9498-E

£39.00 (ex VAT)

£46.80 (inc VAT)

Jaguar D-type style aluminium gear knob but with the correct 5/16\" UNC thread to fit an E

Crank Front lip seal sleeve 24mm wide - Large nose

JAG277

POA (ex VAT)

POA (inc VAT)

Cylinder Block In Alloy (dry sump) #

XKC1636D

POA (ex VAT)

POA (inc VAT)

Aluminium Cylinder block to suit Dry sump. 88mm bores

Split Collets For Valves (Pair)

JAG123

£6.80 (ex VAT)

£8.16 (inc VAT)

Sold in pairs

Cylinder Head Blanking Plate

JAG330

POA (ex VAT)

POA (inc VAT)

Oil Return Pipe For Side Exit Oil Filter

JAGLWE-55-401

POA (ex VAT)

POA (inc VAT)

Connecting Rod - std length

JAG145

£235.00 (ex VAT)

£282.00 (inc VAT)

These steel connecting rods maintain all the important dimensions of the standard Connecti

Oil Pressure Take Off Union

JAG361

£6.85 (ex VAT)

£8.22 (inc VAT)

1/8th bsp pressure fitting

Main Bearing Shells Std - reduced rear shells.

JAG216R

£102.50 (ex VAT)

£123.00 (inc VAT)

When using C&G full race cranks the rear shell requires thinning. These shells have the re

$Lightweight one piece flywheel & 104T ring gear, 7 1/4\" clutch$

Lightweight one piece flywheel & 104T ring gear, 7 1/4\" clutch

JAG171

POA (ex VAT)

POA (inc VAT)

Piston 88mm (Wide angle) 10:1

JAGLWE-55-036

£168.00 (ex VAT)

£201.60 (inc VAT)

Wide angle cylinder head piston. Gives 10-1 compression with our cylinder head. Ideal for

LWE Diff housing and cover in magnesium #

4HU-004-25MASM

POA (ex VAT)

POA (inc VAT)

Manufactured from sand cast magnesium with chromate black finish. Case assembly as supplie

$Exhaust valve W/A 1 11/16\" dia$

Exhaust valve W/A 1 11/16\" dia

JAG193

£30.50 (ex VAT)

£36.60 (inc VAT)

This part only fits Wide angle cylinder heads, 1.6875 diamter

$Clutch Cover 9 1/2\"$

Clutch Cover 9 1/2\"

JAGLWE-80-003

POA (ex VAT)

POA (inc VAT)

Requires JAGLWE-80-004 release bearing.

Belt For Water Pump & Dynamo length 1010mm

C19524

POA (ex VAT)

POA (inc VAT)

We stock parts and cosumables for:

Your filters

Filter by

Jaguar parts
Model: E-Type

QUICK ENQUIRY

We stock parts and cosumables for:

Your filters

Filter by

Jaguar parts Model: E-Type

QUICK ENQUIRY

Jaguar parts
Model: E-Type